CONTINENTAL INDUSTRIES

TULSA, OK 74145-4707 US

Telephone: 918-455-4503/918-663-1440

Cage: 55954

1.0 MG/M3 DUST, 0.1 MG/M3 FUME (MFR).

CAS: 1317-38-0

RTECS: GL7900000

Fraction By Weight: 83%

OSHA PEL SEE INGREDIENT NAME

ACGIH TLV: SEE INGREDIENT NAME

ALUMINUM/COPPER ALLOY

CAS: 12608-74-1

Fraction By Weight: 13%

ACGIH TLV: 1.0 FUME (MFR)

1 MG/M3 OXIDE FUME (MFR).

Fraction By Weight: 1%

ACGIH TLV: SEE INGREDIENT NAME

FERRO SILICON

Fraction By Weight: 2%

OSHA PEL 15 MG/M3 (MFR)

LITHIUM FLUORIDE

CAS: 7789-24-4

RTECS: OJ6125000

Fraction By Weight: 1%

OSHA PEL 2.5 MG/M3 (MFR)

ACGIH TLV: 2.5 MG/M3 (MFR)

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:BURNS FROM CONTACT WITH REACTION OR
REACTION PRODUCTS OR FROM EQUIPMENT. DUST AND FUMES ARE IRRITANT TO
EYES & UPPER RESPIRATORY TRACT. INHALATION OF HIGH CONCENTRATIONS
OF FRESHLY FORMED OXIDE FUMES & DUSTS IN THE RESPIRABLE PARTICLE
SIZERANGE CAN CAUSE INFLUENZA-LIKE ILLNESS TERMED METAL FUME FEVER.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:STANDARD TREATMENT FOR BURNS IN EVENT OF CONTACT WITH MOLTEN
METAL SLAG OR HOT EQUIPMENT. INHAL: FOR DUST/FUMES, REMOVE FROM
EXPOSURE. PROVIDE FRESH AIR. EYES: FLUSH WITH WATER FOR AT LEAST 15
MINUTES , CONSULT MD. INGEST: GET MD IMMEDIATELY .SKIN:FLUSH WITH
COPIOUS AMOUNTS OF WATER. CALL MD .

Flash Point:>175F/>954C

Spill Release Procedures:ALL UNUSED, SPILLED MATERIALS MAY BE SWEPT UP
FOR DISPOSAL IN ACCORDANCE WITH METHODS OUTLINED BELOW, AND
FEDERAL, STATE AND LOCAL REGULATION.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:MATL SHOULD BE KEPT DRY & STORED IN
"NO SMOKING OR OPEN FLAME" AREA. RESTRICTION TO AUTHORIZED
PERSONNEL IS RECOMMENDED. (SEE MSDS FOR ADDNL INFO.)
Other Precautions:FOR ADDITIONAL INFORMATION, SEE AMERICAN NATIONAL
STANDARD, SAFETY IN WELDING AND CUTTING, Z49, I, AND INSTRUCTIONS
PROVIDED WITH MOLDS. CAUTION TO USER TO AVOID DIRECT EYE CONTACT
WITH "FLASH" OF LIG HT FROM REACTION.

Respiratory Protection:NORMAL USE PRECLUDES USE OR SPECIAL PROTECTION
AS MATERIAL IS GENERALLY USED OUT OF DOORS, IN SMALL QUANTITIES,
AND IS OF SHORT DURATION.
Ventilation:LOCAL EXHST MAY BE NEC IF USED IN CONFINED SPACE. USE OF
OSHA APPRVD RESP FOR DUST/METAL FUMES IN LIEU OF LOCAL EXHST.
Protective Gloves:RECOMMENDED FOR HANDLING OF HOT EQUIP.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:EMERGENCY EYE WASH AND DELUGE SHOWER .
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
FIRE/EXPLO HAZ: VOLATILE, COMBUSTIBLE DECOMPOSITION PRODUCTS PRODUCED
FROM COPPER OXIDE AND ALUMINUM.

Hazardous Decomposition Products:TYPICAL OF PROBLEMS ASSOCIATED WITH
MOLTEN METALS.

Product ID:THERMOWELD WELDING MATERIAL
MSDS Date:01/01/1987
FSC:3439
NIIN:00N017664
MSDS Number: BLZMK

Waste Disposal Methods:1) BURIAL IN GROUND AFTER SUBMERGING IN MIXTURE
OF SAND & WATER (CONTACT FACTORY); 2) DISPOSAL BE REACTION OF
CONTROLLED QUANTITIES UNDER CONTROLLED CONDITIONS (CONTACT
FACTORY). DISPOSAL MUST BE IN A CCORDANCE WITH FEDERAL, STATE &
LOCAL REGS .

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.